We have encountered the article about How to Install a Bathtub Yourself below on the net and reckoned it made good sense to share it with you on this page.
Installing a tub isn't precisely rocket science, but it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately difficult project. If the old tub is conveniently obtainable, the job can move rapidly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. See to it you have actually qualified yourself for the work as well as are comfortable attempting it. As opposed to hiring a contractor to take control of a halfway-completed project, it is better to think about employing one prior to you start. Chances are you might require an expert plumber to make tube connections.
This write-up will help you mount a new bathtub in your washroom if you have already acquired a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your devices as well as material list need to make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the water system. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite troublesome because of the restricted gain access to that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will originate from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap ports. The former kind must be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the required position. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up faucets, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Activate the water and also inspect all joints as well as new pipework for leaks and also tighten them if essential. Fill up the tub and also examine the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized at least when as this will certainly settle it right into its last setting.
Preparing for the Installment
First of all, the supporting structure provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bathtub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and also possible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on another blog. Enjoyed our write up? Please share it. Let someone else find it. Thanks so much for your time spent reading it.
Show Details